at-hdvs-txs_dl-web4

Dual HDMI and VGA/Audio to HDBaseT Switcher Transmitter

A newer version of this product is available as the AT-HDVS-150-TX.

Model Number: AT-HDVS-TX

  • 3×1 HDBaseT™ switcher transmitter
  • Long distance HDMI extension
  • Auto-switching
  • Front panel Input Select button
  • Auto display control
  • Front panel Display On/Off control
  • Three way power
  • Multi-channel audio compliant

NOTE: A newer version of the AT-HDVS-TX is available as the AT-HDVS-150-TX in the HDVS-150 Series. Please visit the HDVS Series overview page for more information.

Dual HDMI and VGA/Audio to HDBaseT Switcher Transmitter

The Atlona AT-HDVS-TX is a 3×1 HDBaseT™ switcher transmitter for HDMI and VGA transmission with display control over category cable. It features two HDMI inputs plus a VGA input with 3.5mm audio connector. The transmitter combines the benefits of a switcher with built-in auto switching and the advantages of long-distance signal extension over a single cable. AV signals up to 1080p/60Hz and 1920×1200 video with embedded multi-channel audio and control signals can be extended up to 230 feet (70 meters). The flexible transmitter can work off a local power supply but also supports Power over Category cable (PoCc) to either receive remote power from a receiver or provide power to a remote receiver. Designed for use with the AT-HDVS-RX receiver, the transmitter/receiver pair enables auto display on/off, auto-switching, 3rd-party control, and other features. The AT-HDVS-TX is ideal for long distance transmission and display control in corporate or educational settings using analog and digital sources.

Note:  To eliminate unnecessary waste from installations using remote switcher-based powering methods, all AT-HDVS-TX units marked as “Revision E” (June 2015), or later, will no longer include a power supply. Optional AT-PW24V2.7A-CAPT 24 Volt 2.7 Amp power supplies are available for installations not utilizing Atlona switchers.

Features

3×1 HDBaseT™ switcher transmitter

  • Features two HDMI inputs plus a VGA input with 3.5mm audio connector
  • Allows advanced HDMI display devices to be used with legacy VGA sources
  • Note: Audio signals will not pass without an accompanying video signal

Long distance HDMI extension

  • Transmits HDMI and VGA/Audio signals up to 230 ft (70m) @ 1080p over CAT6a/7 and 197 feet (60 m) @1080p over CAT5e/6
  • Uses easy-to-integrate category cable for low-cost, reliable system installation

Auto-switching

  • Selects active input when sources are connected or if there is a change in source power status
  • Eliminates need for complex control system in small AV systems

Front panel Input Select button

  • Overrides auto-switching when two active sources are present
  • Simple manual control allows presenter to maintain control of AV system

Auto display control

  • Automatically changes projector power state as sources are connected or removed from inputs
  • Eliminates need for complex control system in small AV systems

Front panel Display On/Off control

  • Remotely controls display power state; provides alternate ‘Display Mute’ mode
  • Eliminates need for manual operation of display or use of IR remote control

Three way power

  • Supports Power over Category cable (PoCc) to send power to receiver, receive power from receiver, or use with local power supply; Also receives power from AT-UHD-CLSO-612 switcher
  • Simplifies integration by accommodating flexible power source location

Multi-channel audio compliant

  • Supports PCM, Dolby® Digital, Dolby Digital Plus™, Dolby TrueHD, Dolby Atmos®, DTS Digital Surround™, and DTS-HD Master Audio™
  • Allows any multi-channel audio stream to be used within a professional audio system

RS-232 control

  • When used with HDBaseT receivers with RS-232 such as the AT-HDVS-RX, input selection can be made from a 3rd party control system
  • Seamless integration with larger, control system-based AV systems

Field updatable firmware

  • Rear panel USB port provides an easy means for kit upgrades
  • Ensures long term system return on investment

Mounting hardware included

External, international desktop power supply

  • Included with units marked Rev. D and earlier (prior to June 2015).  See AT-PW24V2.7A-CAPT to purchase optional power supplies for Rev. E and later.
  • Allows transmitter to be used with displays that have an HDBaseT input

Suggested receivers:

  • AT-HDVS-RX – HDBaseT to HDMI Scaler Receiver with Display Control
  • AT-UHD-CLSO-612 – 6 input multi-format switcher with HDVS compatible inputs

Compact, 1.46 in (38 mm) high and 5.1 in (127 mm) wide enclosure

  • Easy installation into system racks, lectern, and under-desk spaces
  • Saves rack space and keeps devices out-of-sight when placed in public spaces

Award-winning 10 Year Limited Product Warranty

  • Ensures long-term product reliability and performance in residential and commercial systems
  • Specify, purchase, and install with confidence

 

Analog to Digital Transition

The Atlona HDVS series was designed to smooth the transition from analog to digital displays, allowing advanced HDMI display devices to be used with legacy VGA sources. The series also adds the simplicity and performance of HDBaseT technology to eliminate multiple cable runs and signal degradation that can occur with long transmission lines. Cost-effective and easy-to-terminate category cable provides additional integrator and benefits.

 The AT-HDVS-TX offers auto-switching between both HDMI and VGA inputs. HDBaseT and power over category cable (PoCc™) allow the sources to be up to 230 feet (70 meters) from the display. A single category cable carries both signal, control, and power. Combined with AT-HDVS-RX, display power is easily controlled with the transmitter. Auto Display On/Off eliminates the need for a control system.

 Benefits when used with AT-HDVS-RX

  • Auto display On/Off
  • Auto input switching
  • HDCP management for use with teleconference systems
  • Set preferred input resolution for both VGA and HDMI sources
  • PoCc to eliminate the power supply at the transmitter
  • Enables display control from transmitter
  • RS-232 input selection from 3rd party controller
  • Easy to use software simplifies RS-232 programming

Integrates with CLSO Series Switchers for complex systems

The AT-HDVS-TX is designed for use with the AT-UHD-CLSO-612 in rooms where multiple input zones are required. Two zones, each with an AT-HDVS-TX, provide two HDMI and one VGA input auto-switched to an HDBaseT output for routing to the AT-UHD-CLSO-612 which provides power to the transmitter using PoCc to simplify system installation. This greatly expands the capability of a CLSO-based AV system.

 

What is Auto-Switching and why is it Important to my Application?

 

Atlona Academy – Extenders Best Practices

 

Atlona Academy – HDVS

Specifications

Bandwidth 6.75Gbps Power Consumption 17.2W
Video Video: up to 1080p
VESA: up to 1920×1200
Dimensions
(H x W x D)
1.18 x 4.8 x 4.92 (inch)
30 x 122 x 125 (mm)
Audio passes through up to Dolby TrueHD 
or DTS-HD Master Audio
Weight 0.67 lbs
0.31 kg
Distance 230ft @ 1080p over CAT6a/7
197ft @ 1080p over CAT5e/6
Temperature

Operating
32°F to 104°F
0°C to 40°C
Storage
-4°F to 140°F
-20°C to 60°C
Wall/Table Mountable? Yes HDCP Compliant? Yes
Certifications CE, FCC, RoHS, cULus for power supplies

Package Includes

• 1 x AT-HDVS-TX
• 1 x Under Table Mount Ears
• 1 x 3.5mm Unbalanced Audio
• 1 x User Manual

Note: AT-HDVS-TX units marked “Revision E” (June 2015), or later, no longer include a power supply. See: AT-PW24V2.7A-CAPT for optional 24 Volt/2.7 Amp power supplies.

Documentation

pdf-icon Manual
pdf-icon DataSheet

Declarations Of Conformity

pdf-icon Declarations Of Conformity

Diagrams, Drawings & CAD Files

cad-icon-(1) CAD Files

Related Products

AT-ANC-108D 8-Button Network Control Panel
AT-HDVS-RX Atlona Dual HDMI and VGA/Audio to HDBaseT Switcher
AT-UHD-CLSO-612 4K/UHD 6 Input Multi-Format Switcher with HDBaseT Inputs, Mirrored HDMI and HDBaseT Outputs, and Auto Switching
AT-PW24V2-7A-CAPT 24 Volt 2.7 Amp Captive Screw Power Supply

Similar Products

AT-HDVS-TX-WP Atlona HDMI and VGA/Audio to HDBaseT Wall Plate

AT-HDVS-TX Firmware

Before downloading either one of these drivers, please take a look at these drivers instructions. Click here for more information.

Download Firmware version 1.2.6 Download Firmware version 2.2.6
File Size 180 KB File Size 180 KB
Date 2.16.16 Date 2.16.16

Update 1.2.6 Includes:

  • Fixed audio stuttering
  • Changed audio EDID from multichannel to 2 channel
  • Added ability to toggle baud rate between 9600 and 115200
    • Press and hold ‘Display ON/OFF’ button for 7 seconds
    • When used with HDVS-RX, use RS-232 command ‘WP_BaudrateTx[a]$’ terminated with a carriage return; a = 115200 or 9600
  • Fixed RS-232 issue where commands revert to default commands
  • Fixed resolution issue with older computers

Update 2.2.6 Includes:

  • Fixed audio stuttering
  • Changed audio EDID from multichannel to 2 channel
  • Added ability to toggle baud rate between 9600 and 115200
    • Press and hold ‘Display ON/OFF’ button for 7 seconds
    • When used with HDVS-RX, use RS-232 command ‘WP_BaudrateTx[a]$’ terminated with a carriage return; a = 115200 or 9600
  • Fixed RS-232 issue where commands revert to default commands
  • Fixed resolution issue with older computers
  • Enables Windows 8.1 and Apple PC firmware upgrading
  • Firmware cannot be loaded onto products with V.1.X.X

HDVS Firmware Updates

Download All HDVS Models Firmware, Software and Instructions in one file Download HDVS Updates Now

The AT-HDVS system features two sets of primary versions. Prefix 2.x.x units can be updated with MAC or windows 8 machines while prefix 1.x.x can be updated with Windows 7 machines or below.

Your HDVS unit comes with an alphanumeric serial sticker behind the unit. The last 3 digits show what factory firmware you have. If you a 2.x.x unit; then you can upgrade to a higher 2.x.x FW. If you have a 1.x.x unit, then you can only upgrade to a higher 1.x.x FW. Please make sure to upload the correct firmware for each unit as not doing so can cause errors.

Note: For AT-HDVS-TX-WP only, a batch had a misprint of “3052” on the alphanumeric tag, if you have this, then it indicates you are on “210” firmware.

AT-HDVS-TX Downloads

Download Control Software Version 2.2.4
File Size 6.3 MB
Date 02.16.16
Software 2.2.4:

  • RS-232 control software for HDVS-RX. Program connected transmitters (AT-HDVS-TX-WP or HDVS-TX) to turn displays on/off with the push of a button, or control video and scaling on the HDVS-RX.
  • Install included font file to work with Windows 10

Click below for Support details

Dual HDMI and VGA/Audio to HDBaseT Switcher Transmitter