AT-UHD-CLSO-824 Firmware

Firmware AT-UHD-CLSO-824 Firmware 2.0.22
File Size 634 KB
Date 12.04.19

Note: Atlona strongly recommends firmware updates using the Atlona Management System (AMS) or the unit’s webGUI. Firmware can also be updated via USB from a PC with Windows 7, or a Mac running Windows 7 in Bootcamp.

AMS allows management and automation of firmware updates for multiple Atlona IP-controllable products in an AV installation. With AMS, you can push new firmware to several devices at once, and also schedule updates at a convenient date and time.

Release Notes

Version 2.0.22

Features

  • Added audio mute toggle function to the WebUI, allowing all audio to be muted.
  • Added ability for the unit to accept RS-232 commands from the HDVS-200-TX/WP. Zone commands will automatically be passed to assigned output. NOTE: This requires that the HDVS-TX/WP is running firwmare 2.0.64 or higher.
  • Added ability for the unit to accept RS-232 commands from the HDVS-210U/H. Zone commands will automatically be passed to assigned output. NOTE: This requires that the HDVS-210U/H is running firwamre 1.0.38 or higher.

Bug Fixes

  • Fixed an issue where HDCP content to a non-HDCP sync would cause video flickering and slow response time.
  • Unit can now toggle between DHCP and static IP modes from the front panel.

Known Issues

  • Unit will not show the IP address of the HDVS-SC-RX IP in the WebUI.
Previous Releases
Version 2.0.16

Features

  • Added AT-HDVS-210U-TX-WP / AT-HDVS-210H-TX-WP compatibility.
  • Added the ability to make changes to the system in Web UI while unit is in Standby mode.
  • Added customizable hostname support.
  • Added the System sta API command.
  • Added the Input sta API command.

Bug Fixes

  • Fixed an issue with custom passwords being lost.
  • Under specific network configurations, when microphone ducking was enable on both mic inputs, while using all outputs, Telnet sessions would be slow to respond and would often result in a time-out or command failure.
  • Resolved microphone ducking issue; this feature is now functional.
  • Microphone volume no longer changes after power-cycling the unit.
  • Fixed an issue where using the VGA port, audio would not be passed if using the 3.5 mm analog input with the AT-HDVS-200-TX.
  • Network connection is no longer lost during the firmware update procedure.
  • Improved performance of the Web UI.
  • Unit no longer locks up during a system boot-up, when polling is used.
  • Resolved issues with Amazon Basic VGA cables not working correctly.

Known Issues

  • Incorrect receiver is reported in the Web UI when connected to an AT-HDVS-SC-RX.
Version 2.0.08

Features

  • Added the ability to switch between DHCP and static IP through the front panel.
  • Added CLI debug command

Bug Fixes

  • Resolved an issue with some VGA cables not working.
  • Resolved issues regarding polling the device status and lockups.
  • Resolved loss of analog audio from HDVS-200-TX when connected to the AT-UHD-CLSO-824
Version 1.0.28

Features

  • Added the ability to switch between DHCP and static IP through the front panel.
  • Added CLI debug command.

Bug Fixes

  • Improved compatibility with AT-HDVS-200-TX.
  • VGA audio no longer incorrectly mixes with input audio when Auto Follow Other Video (AFOV) is selected.
  • Fixed consistency with HDBaseT projector video.
  • Updating DSP firmware no longer causes audio to drop.
  • Fixed IP control to improve speed.
  • Unit no longer locks up when network security software scans the unit.
  • HDVS-200-RX no longer loses audio when rebooted while connected to the UHD-CLSO-824
  • Fixed webGUI home page showing incorrectly at different resolutions.
  • Video flashing no longer occurs with HDBaseT projectors.
Version 1.0.23

Features

  • Unit now receives feedback over TCP/IP and RS-232.
  • IP command response speed increased.

Bug Fixes

  • VGA audio now plays correctly when configured to AFOV.
Version 1.0.15

Features

  • New command “HDVS sta” added to display IP of connected HDVS units.
  • HDVS-200-TX and HDVS-150-TX display control through IP now compatible with the CLSO-824.
  • Zone commands now pass through to the HDVS-200-RX via IP or RS-232.
  • Users can now connect by IP when Login mode is enabled.
  • Stored EDIDs are now selectable in the memory slots of the webGUI.
  • HDVS-200 now compatible with HDVS page of CLSO-824 webGUI.

Bug Fixes

  • Adjusting audio while muted no longer unmutes or creates audio stuttering.
  • HDVS page within the webGUI now correctly displays switch information.
  • VMicX Y now returning correct feedback values over RS-232 and IP.
  • CLSO-824 no longer locks up when the webGUI is refreshed rapidly.
  • Incorrect RS-232 zone command no longer lock up the CLSO-824.
  • CLSO-824 no longer resets the HDVS-150-TX back to default settings when connected.
Version 1
  • Factory firmware